Airport Vehicle adapted with half cabin.
Short vehicle Half Cabin with 7000kg GVW and 10.000 GVW with wheelbase between 3.200 mm and 3750mm aprox. Lifting height from 1.300mm to 4.000mm.
Our JOFR-03 is suitable for Airbus A319, A320, A330/340, etc. and Boeing B-787 or similar aircrafts resupply, with lifting height from 2300/2900mm up to 6000mm. Built on any truck brand available, Mercedes, Benz, IVECO, Renault, Volvo, Man. GVW within 7 and 10Tn.
Isotherm or Refrigerated autonomous or connected equiment available. Main brands installed are Thermo King, Carrier or Zanotti Conditioning/Refrigeration systems.
Electrical system available on CANBUS installation. Remote diagnosis via System Modem optional.
Main Features
- Chassis: Volvo, Iveco, Renault.
- Cabin: Half Cabin, A/C Optional.
- Lifting System: Jofrauto Branded
- Electrical System: CANBus or Standard
- Remote Diagnosis: Optional System-Modem
Certifications and Standards
IATA AHM-904 AHM-910 AHM-913 AHM-915 AHM-927
Technical Specifications
| Element | Measure |
|---|---|
| Maximum Lifting Height | 4.000mm |
| Mínimum Height | 1.300mm |
| Body Width | 2.400mm |
| Body Length | 4.300mm |
| Total Length | 6.500mm aprox |
| Total Height | 3.700mm aprox |
| Wheelbase | 3.750mm |
| Cabin Type | Half Cabin |
| Suspension | Mecánica |
| Gearbox | GearBox Manual/Auto |
| GVW | 7Tn, 10Tn |
Technology and Equipment
Box
- Van Body manufactured on 70mm sandwich panel. 4000mm exterior legnth, 2300mm exterior width and 2300mm exterior height.
- Front and rear sliding doors.
- Fabricada en lámina de vetroresina blanco TH.
- Manufactured in white GRP laminates.
- Front and rear clearance lights and two ceiling recessed led lights.
- Special wiring for rear and front camera installation.
- Frontal reinforcement for front guides assembly.
- Floor finished in rice grain patterned type fiber with trolley fastener.
- Special fastener for trolleys
- Auxiliary chassis body assembly
- Reinforced steps at rear side for body access
- Stainless Steel handlers on rear door
- Frontal reinofrcement for Colling assembly
Lifting System
- Scissors lifting system with 4000mm maximum working height and 1300mm minumin height.
- Built over auxiliary UPN chassis of 140mm and 100mm chassis. Scissosr built with structural frames rails 160 x 80 x 8mm and flat bar reinformcements of 70 x 10mm along all perimeter.
- Hydraulic equipment consisting on two cylinders, four stabilizing cylinders and one cylinder to move platform forward/backwards
- 24v Pump motor installation and manual pump for emergencies.
- Transfer platform to aircraft made with structural tubes with sliding capacity forward and flip down hatch. Floor platform made in non‐skid aluminium.
- Maximun height stop sensor
- Scissors lift grey painted
- Extensible handrial 900mm height.
- Rear steps body access.
- Warnings and security signaling stickers.
Electrical System
- Manufacture and assembly of electrical safety according to airport regulations AHM 927, switchboard connections and two boxes of manoeuvres, one cabin inside and another on the inside of the van body.
- Light timer installation inside body.
- Vehícle configuration.
- Wiring diagran with CE Certificacion.
- LED headlight on transfer platform working zone.
- Rear cámera and monitor installation
Cooling System
- Zanotti, Thermo King, Carrier.
- Catering truck assembly.
Documents
- User manual (soon available)
- Comercial Brochure (soon available)
For further information, contact us